This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| hellohome:node:node [2017/01/26 15:21] – [Requirements] vdesmedt | hellohome:node:node [2025/10/26 08:43] (current) – created kayleighbusch42 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Node ====== | + | Oklaro rewards its players |
| - | + | ||
| - | * [[./ | + | |
| - | + | ||
| - | ===== Node types ===== | + | |
| - | + | ||
| - | * Energy monitoring | + | |
| - | * Powered by battery or on main | + | |
| - | * 2 Hal, 1 Strait | + | |
| - | * 4 current sensors | + | |
| - | * Environment sensors | + | |
| - | * Relay nodes | + | |
| - | * Powered by main | + | |
| - | * Can switch N relays | + | |
| - | * Can measure current through each relays | + | |
| - | * Environment sensors | + | |
| - | * Switch nodes | + | |
| - | * Powered by main | + | |
| - | * Fits in wall sockets | + | |
| - | * Has N push buttons | + | |
| - | * Has N leds | + | |
| - | + | ||
| - | + | ||
| - | ===== Pin Assignment ===== | + | |
| - | + | ||
| - | + | ||
| - | ==== Requirements ==== | + | |
| - | * Two HAL : 2 Dig | + | |
| - | * One Dry Pulse : 1 Digi | + | |
| - | * Temp and Humidity : I2C | + | |
| - | * VIn : 1 Ana + 1 Digi (trigger) | + | |
| - | * Two Push Buttons (2 Digi) | + | |
| - | * 4 Digital Output (4 Digi) | + | |
| - | + | ||
| - | Total : | + | |
| - | * I2C | + | |
| - | * 1 Ana | + | |
| - | * 8 Digi | + | |
| - | * 1 Interrupt | + | |
| - | + | ||
| - | ==== Notes ==== | + | |
| - | * One xx can be used to monitor multiple inputs with the helps of diodes | + | |
| - | * Digital inputs can be extended with I2C Digital extender | + | |
| - | * Analog inputs can be extended | + | |
| - | * We can easely read 5 digital inputs | + | |
| - | + | ||
| - | ==== Assignment ==== | + | |
| - | The moteino has 22 a/d pins from which some are reserved for the internal use of the moteino (flash, rf) | + | |
| - | + | ||
| - | {{ : | + | |
| - | + | ||
| - | * D0,1 : Serial | + | |
| - | * D2,10-12 : Transceiver | + | |
| - | * D3 : Interrupt | + | |
| - | * D4 : HAL1 | + | |
| - | * D5 : HAL2 | + | |
| - | * D6 : Dry Pulse 1 | + | |
| - | * D7 : Vin Trigger | + | |
| - | * D8,11-13 : Flash | + | |
| - | * D9 : LED | + | |
| - | * D14 : Push Button 1 | + | |
| - | * D15 : Push Button 2 | + | |
| - | * D16 : Free | + | |
| - | * D17 : Free | + | |
| - | * D18,19 : I2C | + | |
| - | * A6 : Vin | + | |
| - | * A7 : Free (Could be up to 5 input based on voltage divider) | + | |
| - | * I2C 8 Port Extender : DOUN 1-8 | + | |
| - | + | ||
| + | If you have any queries about the place and how to use [[http:// | ||